Section: System Managers Manual (8)
Updated: Last change: Aug 2016
lircd-uinput - Forward lirc button presses as uinput events
lircd-uinput [options]... [lircd output socket]
lircd-uinput [options]... [file]
lircd-uinput reads decoded button press events from a lircd(8) output socket and injects these as key events to the kernel uinput device. The kernel makes these events available to other applications on a /dev/input/event device, just as for any other input device.
lircd-uinput is designed to run as a systemd service.
The lircd output socket argument is an optional path to the lircd output socket. It defaults to the output value in the [lircd] section of the lirc_options config file, falling back to /usr/local/var/run/lirc/lircd.
If a plain file is given instead of a socket it is supposed to contain button press events formatted as documented in lircd(8) . lircd-uinput will in this case send the codes in this file and exit.
In order to work, release events must be sent to the uinput device. See REPEAT HANDLING.
lircd-uinput can only handle button events named using the official namespace i. e., buttons known to the kernel. See NOTES.
Unless the /dev/uinput default permissions are changed lirc-uinput needs to run as root. See NOTES.
The /dev/input/event device created by the kernel can be tricky to locate, and is not stable. See NOTES.
After receiving a keypress events the kernel will start emitting repeat events to applications until lircd-uinput emits a corresponding release event. The release events could be created by lircd(8) using the --release option. Such events typically has an _UP suffix appended to the original keypress event. As an alternative, lircd-uinput can create release events using the --add-release-events option. Combining both of these options might give unexpected results.
In any case, the repeat events generated by the kernel can be tweaked using the --repeat option. This can set the time between the keypress event and the first repeat event and the time between each repeat event. The --repeat option should only be used if no other program or udev rule is automatically setting up key repeat parameters. By design the repeat parameters can't be set in an atomic way during input device registration so this option is prone to race conditions.
.Note that the lircd-uinput repeat-event handling differs from lircd(8) which implements (emulates) hardware autorepeat in the events sent to uinput (event.value == 2). lircd-uinput only sends keypress and release events, trusting the kernel autorepeat support.
By default, the dev/uinput device is not writable for regular users. Thus lircd-uinput needs to run as root unless these permissions are changed.
One way to achieve this is an udev rule. The lirc distribution contains an example rule which makes the lircd-uinput device writable for users in the group lirc. Another way is to use lircd-setup(8) to change the permissions. As distributed, the lirc_options.conf file contains an commented example using setfacl(1) .
lircd-uinput can only forward lircd button events with names from the legal namespace defined by the kernel. A complete list of possible button names is available in /usr/include/linux/input-event-codes.h and also using irrecord -l . Other button names are silently dropped.
The event keycode depends on the name that was given a button in the lircd config file e.g., if the button is named KEY_1 the keycode 1 will be generated.
The kernel makes the events generated by lircd-uinput available on a /dev/input device like /dev/input/event12. This device name is not stable and typically varies after a reboot. The lirc distribution contains a udev rule which if installed creates a device link named /dev/lircd-uinput which always can be used.
lircd-uinput is designed to replace the currently deprecated --uinput option to lircd(8). However, lircd-uinput forwards all events unless blocked by the --disabled option. On the other hand, lircd --uinput does not forward all events - the heuristics used has been changed over versions.
Since the device name is fixed, only one instance of lircd-uinput can run on a system.
This document was created by
using the manual pages.
Time: 19:29:43 GMT, August 09, 2016